Wiring it all up

The bike is now loaded with most of the components that it needs, although I have to say I have not put the mechs in the correct positions. In fact I am not even sure what the correct postions for these are! I am sure a little reading and a lot of fiddling around will sort this out. The chain will have to wait until this is completed.

I have cabled up the brakes which was a comparatively simple job. On this bike the brakes are of the cantilever style, which to look at the forum were going out of style in favour of the better stopping power of V style brakes. I am pleased to see that the brakes have made a come back, mostly due to the style conscious fixie couriers who clearly prefer them for some reason.  Not quite an evolutionary dead yet.

Cabling the brakes was simple as the brakes have a fixed length of cable defined by the hanger to operate the brakes. The rest of the cable length is actually irrelevant. It doesn't really seem to change the stiffness of the brakes. This means you can get away with bigish loops of  cable in the housing. Which is exactly what I didn't do, and I am now regretting the rather measly amount of cable I gave myself for the front brake. It is not affecting performance but it does look slight inelegant. I'd go back and change it, but that would mean a new cable and I am loathe to buy more just to satisfy a little bit of artistic flare. It can be correct when the brakes need changing again.

Cursing and fumbling with a 10mm spanner and a 5mm Hex key I remember that there is a pay off for canti brakes. Each brake block is adjustable. Fantastic for getting the perfect fit, but then again each of the two pairs of brake blocks needs to hit the rims at exactly the same point in time. Time slows as I fiddle moving blocks back and forward, fingers cramping from holding spanners and pulling brake levers. Back is aching from leaning over the bike until the stopping power of the brakes can be applied cleanly and evenly. "Think of it as a pay off", I tell myself "in the wet weather when a car decides to stop suddenly or turn across you. Then the bike will stop in a straight line and not slew across the road."
"Or I could just not cycle in the rain!" I reply.

I am now left with a large amount of cable housing and some spare cable. The housing is fine, there is always a need for housing and it fits both brakes and and gear cables. But the cable is a different matter. You can't use it on the bike to replace cable so what can you use it for. I am sure there is some hidden purpose for which it could usefully be employed. But what?

Stripped naked

One frame stripped and cleaned with the exception of the the bottom bracket and the headset. The reason for this is that both are moving smoothly and I have no desire to introduce dust and dirt into the bearings without reason. Looking at the cantis I decided that they could do with a good clean. There was a lot of road crud round the mounting bosses and while everything is off it made sense to clean right down.

Of course this causes a little confusion as when confronted with assembling something that you have got so used to seeing daily there is a moment of "how does it go?". A little bit of logic thinking though solves most problems and it was easy to see how the cantilevers fitted together. I was a bit thrown by the cable routing for a moment but that is because the line runs across of the back of the seat tube.


The cassette was really the only issue for the strip down. I have a Shimano lock ring tool for removing the lock ring (obviously). It is not a particularly expensive one coming as it did as part of a Halford's basic maintance kit. It does work though as it was used to do the work on the cassette of the P3 (Cassettes and Remasters). This time though it would not budge and was in danger of stripping all the splines off the tool. In fact it has done enough damage that I am going to have to get a new one.

Well and truly beyond the shifting with my short arm ratchet spanner and my middle aged bulk, after soaking in GT85 and a tap or two with a hammer to break and magnetised bond. I was down to a blowtorch (I don't have one), a longer spanner (I don't have one) or an angle grinder (I don't have one). Rather than fork out more than £40 for one of the above I thought I will give a local bike shop a call and see if they will take on the job. Having not got anywhere positive with one "local" bike shop. I say local because as you know they are a significant drive from central Croydon. I tried the other in Beckenham - "yes" said Deen's Garage in Beckenham. Not only did they happily apply a longer lever to the problem they also didn't charge a workshop fee because it was a quick job.

They say it easier to destroy than create. Now is the time when I find out if this is true. A bike that has served as a faithful servant riding across the West country along the Bristol to Plymouth route and over Welsh hillsides, as well as recent commuting to and from Greenwich, is about to have a make over.

And so the Legacy begins

In the absence of any project bikes, and despite my recent experience with bits falling off the P3 frame (must buy torque wrench). I decided to start work on my hybrid bike. Over the past couple of months I have been assembling a series of spares to overhaul the quite frankly knackered shifters and the aging drivechain parts. The experience of changing gears has reached the top end of tempermental. Which is to say the occasional inconvenience of forgetting your house keys as opposed to the Alzheimer memory loss.

This bike is a Ridgeback Adventure SX120 - bought back in the early 90's and still going strong. When it was relatively new there was an inadvertant upgrade of wheels and hubs which looks to have been a very positive move as they run as smooth as the day they were fitted. It will also allow me to fit a 9 speed to them taking the range for the cassette from its lowly to 7 and adding a bit of low climbing gears for my tired old legs.

In my previous round of parts purchasing I had picked up some Shimano LX mechs and although I had planned to put these on an MTB build, I have decided that these should be the basis of the equipment change. Should these second hand parts fail then I have the option of buying a new part that will slot into the system. As this is to be a workhorse bike I wanted all the parts to be of a decent level of mechanical soundness. Most LX parts are relatively cheap and the shifters were easily located at a low price due to discontinuation of the items. A 9 speed chain and an HG50 cassette make up the drivechain parts.

The brake levers were also a little tatty and quite frankly as the levers themselves are plastic, I decided that replacement with some Avid Juicy 7's was a nice touch. Finally to complete the comfort rating I am going to add some Ergo grips and a new saddle (the old ones have been on from new, and I'm sure I deserve it).

My first task will be to strip down the bike and clean, I will leave the cantilevers on the bike. I'm not sure I want to go as far as a bare frame rebuild, but when I look at the bike I may change my mind.